Blog

Water Heater Repair Plano Blog

Our blog is designed to give homeowners as much information on general plumbing repair tips, not just Plano water heater repair advice.  Many home plumbing maintenance tasks homeowners can be well equipped  to take care of themselves.  Enjoy!

A Concise History of Water Heaters

Posted by on Jul 6, 2016 in water heater technology | 0 comments

Similar to a bunch of innovations we utilize today, the beginnings of the modern-day water heater can not easily be traced back to just someone or society as its innovator. It could not be as mysterious as some creations however it is absolutely an innovation that we make use of on a daily basis. Having hot water in our houses has actually assisted make our lives much easier and healthier, and should not be something we take for granted.

It makes us laugh a little when we checked out posts and see advertisements for tankless hot water heaters with the advertising message of “instantaneous hot water.” Of course, it would be wonderful to have, and sure it can preserve water that would run down the drain as one awaits the hot water to travel through ones home plumbing pipes from the water heater to the faucet; but are we that spoiled that we cannot wait a few seconds for the heated water to come out? In this short article we are going to be checking out several of the cultures and individuals who have actually aided with the development of bringing hot water into the residence for us to appreciate this modern comfort.

I remember viewing old Western movies when I was a child and people would fill up bathtubs with water heated up from a range or fire. This was a time consuming process, yet just what individuals did before having the creation of a water heater. Over the past 100 years or so, luckily this process is not needed any longer.

The Romans had their hot bath houses, which is usually considered an early type of water heating. They had an exceptional method of heating their buildings with flowing air heated from a fire underneath the flooring. Kind of like an early form of radiant floor heating. They used fires to heat water in huge lead boilers fitted over the heating systems. This was made use of for their huge bath houses which were like saunas.

Now we are going to leap ahead in history to the English painter, Benjamin Waddy Maughan. He had the first patented for a water Maughans Water Heater The Geyserheater in 1868. In his design, natural gases heated up the water yet there was not a flue to get rid of the gas vapors that are created in the process. This was the first time that gas, not a solid fuel was used in heating water. This creation by Maughan had the cold water flow through wires that were warmed by the hot gases of a burner. The heated water produced after that went into a sink or tub. It was called The Geyser, for the inventor had the idea from a real water geyser.

Due to Maughan’s absence of air flow, his water heater was not used inside the house. Today, if a water heater is not vented appropriately, carbon monoxide gas can get into the home, which is a large concern.

Maughan’s innovation did go on to influence Edwin Ruud, a Norwegian mechanical engineer who was the creator of the automatic storage hot water heater in 1889. In the 1880s in Pittsburgh, Rudd started the process of determining ways to develop hot water securely. The firm he began, Ruud Manufacturing Company, is still a leading producer of water heaters today. By the time of Rudd’s death, he managed to alter the everyday sanitary routines of the majority of every American.Rudd Water Heater Patent

The following is from Rudd’s patent:

In a patent obtained by me December 30, 1890, No. 443,797, I have described and claimed certain improvements in Water-heaters, such improvements consisting, generally stated, in certain mechanism controlled by the temperature of the Water in the boiler for regulating the flow of gas to the burner employed for heating the boiler.

The present invention has for its object a construction of the regulating Inechanism, whereby the flow of gas to the burner may be more nearly proportioned to the quantity of cold water admitted; and in general terms the invention consists in the construction and combination of mechanical devices or elements, all as more fully hereinafter described and claimed.

In the accompanying drawing, forming a part of this specification, is shown a sectional elevation of a water-heater having my improvement applied thereto.  (read more. . .)

In England around 1895, Ewart & Son released a gas fired hot water heater called the Royal Geyser. It would certainly be mounted next to a bath tub. It was gas fired and heated water which was going into the bathtub. The hot water was mixed with cold water to create the temperature level one wished. The invention was a little fragile, for if the water was turned off prior to the pilot light being switched off, it would normally mess up the heater.Ewart Royal Gyser Water Heater

The 1900s are viewed as the golden era of hot water heater. There are lots of firms that began in the USA, providing new ideas and modern technologies to continually improve on the general design. We have electric, gas, tankless and also solar water heaters today, all of which have a remarkable past for their creations.

I mentioned tankless hot water heater in the introduction of this . Though many people still consider them a recent product in the plumbing field, but they were really first developed in 1929! Stiebel-Eltron created the first electrical tankless heater, or coil immersion heater.

Other terms utilized to refer to hot water heater that are still around today are an electric water boiler, electric dispensing pot, geyser, or electric water urn.

There is a succinct history of the contemporary water heater. Aim to remember that it is a house device that does require a little maintenance now and then as well. Ideally our Plano hot water heater clients will certainly have the ability to not take their water heater for granted more and will see to it to comply with proper maintenance steps.

Smart Water Heaters

Posted by on Jun 23, 2016 in water heater technology | 0 comments

It is popular opinion, and the United States Department of Energy informs us this too, that heating water uses around 18 percent of the normal residence’s yearly energy consumption. The only other home device that uses more is the heating and cooling system. With the common tank hot water heater that a lot of residents make use of, it is maintaining 40 to 50 gallons of water hot all day regardless of when it is being made use of. Generally with this scenario, 20 to 50 % of the energy being used is totally thrown away. What are some alternatives to assist curb this power loss? The company Aquanta, use to be called Sunnovations has actually been developing a sensible solution for a number of years now.

Sunnovations had a crowd-funding campaign in 2014 that did not get to its full funding however that is alright with them for they had the ability to amass lots of interest from distribution partners that has proved fruitful with a 2nd go around now. Aquanta is presently taking pre-orders on a brand-new smart water-heater controller, which they hope will certainly be delivering in July of this year.Aquanta Water Heater Controller

Aquanta’s CEO Matthew Carlson says that the business’s new modern technology has actually been field tested for a year now. It is surprising that other businesses have not started working on a comparable device, particularly with the preliminary crowd-funding campaign … even with it not being successful for them originally. Since hot water heater usually have a life of 8 to 12 years, it is not rational to replace it when it is functioning well, however just does not have all the contemporary technology that a new hot water heater could come with. Numerous new water heater models are using smart innovation functions, but there is nothing that will function with any type of type of current hot water heater to “make it smart.” Sears recently put out a hot water heater controller that will work on some of its models, however not every one of them and not on different companies hot water heaters.

The only other device that is only a little comparable is a water heater timer. But it functions like a timer, turning the heater (and just electrical water heaters) on and off at specific times of the day; and not via smart technology.

Among the functions of the Aquanta technology is that it will certainly “learn” what the water use patterns are in the residence. Most people tend to shower, run the dishwasher and other hot water utilizing home appliances around the very same time of day. The device will work to readjust the water heater’s temperature level to meet the need throughout peak times, and lower the energy usage during non-peak times.

The Aquanta will be positioned in addition to a water heater. A probe is set up behind the T&P valve port and after that the probe is connected to the controller. A second sensing unit gets taped to the cold water supply. An optional third probe is made to spot if there is a water leak from the water heater as well.

Finally, the controller is connected to a Wi-Fi network and homeowners will download the smartphone app on a phone. The controller links to Aquanta’s cloud-based server and begins its job of discovering the home’s hot water use patterns. It is likewise possible to manually enter in the water usage pattern too. So, it can manually and automatically regulate the heater’s power use.

It is made so a handy resident can do the setup him or her self. If a property owner doesn’t feel up to the activity, a plumbing specialist can absolutely help the firm states. Aquanta approximates it taking around 40 minutes for a house owner to complete the set up.

The system will work with the majority of water heaters, no matter the fuel source. It depends upon the source of power if it will work or not. There needs to be an electronic ignition system, which most all newer water heaters will certainly have. Old gas heaters might not however. Definitely take a look at the compatibility info on the business’s website here first.

Precisely just how much energy, and then translated into money, can a home owner conserve with the system? Right here is what Aquanta states on their site: “our data suggest that at least 20% and up to 50% of that energy in a typical home is wasted through ‘standby loss’. We are being careful to not overpromise, and have 3rd party testing underway to more specifically quantify the saving opportunity. However, our internal studies and modeling suggest that between 10-30% of water heating energy can be saved by intelligent control through Aquanta. The economic value of intelligent control of water heaters is much higher when factoring in peak or time-of-use pricing and utility peak demand reduction and similar incentives.” (read more here)

What others around the internet are saying:

www.greentechmedia.com

www.treehugger.com

Back to our blog. . .

All About Plano Tankless Water Heaters

Posted by on Jun 23, 2016 in Tankless Water Heater Repair Plano, Water Heater Replacement Plano | 0 comments

For when you want a replacement water heater for your Plano office or home, a tankless water heater may be a possible choice. Lots of people still think of them as a really brand-new fad in hot water heating and are unclear regarding just how they operate, exactly what the cost for them is, and exactly what kind of maintenance they will need. These are a few of the subjects we will certainly review about tankless heaters in this short article. As compared to standard tank heaters, generally they are 8 to 34 percent more power efficient, supply an endless supply of hot water, could operate twice the life-span, and require only around one-fifth of the physical space as other heating units. Let us initially look at how tankless water heaters work.

How Tankless Hot Water Heaters OperateTankless Water Heater Installation Plano

Tankless water heaters are additionally termed on demand water heaters. This is extremely suitable for they only heat water as it is needed … on demand. The traditional image most individuals have of the big storage tank water heater in the basement or garage, is constantly heating fresh or the same water inside its tank all day long. It should make sense that this is far more efficient compared to making use of power to keep water heated. Think of it like maintaining a pot of water warmed on ones range all day to be prepared for when one desires a hot cup of something to drink.

In straightforward terms, here are the actions involved. The property owner switches on a hot water tap in the house. Cold water then travels down a pipe and into the tankless hot water heater. An electric element or gas burner (depending upon the energy source for the tankless heater) switches on when it knows hot water is desired. The heating element is powerful enough to heat the water immediately as it travels through, then on its way to the hot water tap.

Effectiveness and Flow Rate

The standard flow rate is to be able to offer two to 5 gallons of hot water each minute. Gas burning tankless units normally have a greater flow rate than electric units. However, gas heating systems have to have an IID, or intermittent ignition device, installed. What this device does is only enable the pilot light to turn on when water is required. Hot water heaters without it will certainly waste power for the pilot light can be regularly burning. If the reason of using a tankless hot water heater is to save money on energy usage, after that it just makes good sense to have one of the most power reliable design possible.

It is this restricted flow rate that is probably the largest disadvantage to a tankless version. A large version may not be able to supply the quanity of hot water required if let’s imagine a dish washer and shower were running at the same time. One alternative is to be cautious of just what warm water using gadgets are being utilized at the same time. That is not also hard to do.

Another means to get rid of the minimal flow rate is by setting up more than one tankless water heater in the residence. Given that they are so small and compact, property owners can install devoted tankless units right where they may be required, such as in the kitchen, in the utility room or near individual bathrooms. This will relieve the flow rate restriction extremely quickly.

If one does not wish to originally make use of a tankless style in the whole home – let us to say that there is no need to upgrade the present water heater yet. Or, if a hot tub is added, or a new living space is added to the residence is constructed the current traditional water is not large sufficient to provide the required hot water all over, a tankless version can be used an extra heater for merely one or a few areas. It can likewise excel at supplementing a solar water heater also.

Currently let us consider energy effectiveness of a tankless hot water heater. Houses that consume less than 41 gallons of hot water a day might provide a 24 to 34 percent boost in water heating efficiency with a tankless version. For those that utilize a great deal of water, around 86 gallons of hot water per day, can still obtain 8 to 14 percent power savings. Though this is a larger hot water heater installation cost, however as much as 50 percent power financial savings are possible with several tankless devices near particular hot water electrical outlets.  (http://energy.gov/energysaver/tankless-or-demand-type-water-heaters)

Tankless Water Heater Setup and Upkeep

Plano Tankless water heater installments are a bit more complex than a conventional water heater. It seems everybody knows a pal or has a family member who could set up a hot water heater. Certainly that can conserve a homeowner a little money, however by having an unlicensed person do it, it could nullify the service warranty. A trained expert is required for the installation to guarantee it works appropriately and supplies the efficiency one is trying to find. There are environment, security aspects, local building ordinance needs that all have to be taken into account.

Just like any type of water heater, doing maintenance is essential to do in order to expand the life of the heater and to maintain it running at peak effectiveness. The owner’s guidebook will certainly have upkeep recommendations. The main one is to clean the interior with vinegar and flushing out the system.

With having us effectively set up and assist to preserve your new tankless water heater, it could conveniently last twenty years or longer. That alone is a lot longer time compared to a traditional water heater. Obviously we are right here to help with any kind of tankless hot water heater repair in Plano TX that could be needed also.

Warning Signs of Hot Water Heater Failure

Posted by on May 23, 2016 in Water Heater Repair Plano, Water Heater Replacement Plano | 0 comments

The hot water heater in ones Plano home should last a very long time without needing to have a lot of repair services performed on it. There are some easy upkeep steps house owners should be doing in order to help see to it will certainly last a truly long time without requiring numerous, if any type of, repair services, which we have already discussed here.

There could come a day, however, when no, or not sufficient hot water comes out of a faucet like it used to. This article is going to look at exactly what to do when the hot water heater is not creating hot water. There are several reasons that this could happen, and a number of indications the water heater has actually given that house owners normally will miss out on. We will certainly not be judging property owners for missing these signs. Nonetheless, there are some significant things that will certainly occur eventually, to allow one understand exactly what either a major repair is required, or it is close to completion of the hot water heater’s life.

Just How Old is the Hot Water Heater
If the house one lives in was purchased, it is easy to not know just how old the hot water heater is. Water heaters will continue to function for years, sometimes much longer than the number of years it is made to run. Because of this, it is very easy to overlook the last time it was changed. So, if home owners offer it just a little attention, one will certainly be stunned at the length of time the heater will run well.

There is an identification number on the water heater that will state the year it was manufactured. If the heater is greater than ten years old and wants some major repairs, replacing it should definitely be thought about.

Is There Discolored Water Coming From the Water Heater
Anytime the water from hot water faucets in the home has a discolored or rusty hue, it typically means there is rust inside the water heater tank. This is not an excellent indication to see. Once the interior of the storage tank begins to create corrosion, it is an eventual reality that the tank will certainly corrode through totally. The important point to look for is water dripping from the storage tank, for it will at some point trigger a large mess if the hot water heater is not changed before the tank rusting through.

However, there can be other reasons the water is discolored. We do not have time in this post to discuss them, however give us a call to discuss what might be happening.

The Water Heater is Making Strange NoisesPlano Water Heater Repairs
With the natural course of a hot water heater operating, sediment will form on the interior of the tank. As it is heated up, and reheated, the sediment will harden, and may lead to lower efficiency. It will take a lot more energy to heat water then. The more sediment that forms will start to cause knocking or popping noises from within the storage tank. They may get quite loud also. It is not as big of a trouble as it could sound to be. The sediment can be removed from flushing the storage tank. We would certainly like to do this process for you, however residents are able to conduct it themselves. For safety and security factors though, we would absolutely want to help.

There is Moisture Around the Warm Water Heater
Anytime wetness begins to gather around the hot water heater it might indicate that there is a small leak or crack in the tank. When metal heats, it expands and may form slight cracks. The older the heater is, the easier this may take place. Nevertheless, do not stress if you see leaking water, for it can additionally be coming from a plumbing connection or fitting that is lose. It could be originating from the T&P valve also. Leaking water appear like a bad indication, however it might additionally be a simple solution or connection tightening up.

If any of these things are happening, connect with us to schedule involving see what the needed Plano water heater repair must be. It is best to allow us handle and servicing done to the system making sure the warranty is not nullified by any maintenance performed by an unlicensed individual.

Water Heater Repairs Plano Texass

From Visually.

Total Water Heater Maintenance Tips

Posted by on Jun 11, 2015 in Gas Water Heater Repair Plano, Water Heater Repair Plano, Water Heater Use and Care | 0 comments

Water Heater Repair Plano is not about to talk about the miserable experiences regarding water heater maintenance of “getting out of bed to the chilled bath,” here. Furthermore, we are going to presume that one recognizes the basic concept of ensuring that ones water heater is maintained regularly to be able to receive the most from its life time. This can certainly help one cut costs on energy costs as well. All of that is practical we realize. Although hot water heaters don’t need a lot with regards to maintenance (and we are amazed, even though not shocked, by how many customers we come across who have not carried out anything to their water heater), listed below are the duties people must be aware of with regards to routine maintenance.

How Long Should My Plano Water Heater Last?

The regular gas water heater can last 8 to 10 years. There are numerous variables that may have an effect on the general lifetime obviously, however this is an excellent standard. In all probability the most significant aspect which will impact the long life of it is usually mineral deposits. Several of the duties below should go a long way in assisting to lessen the accumulation of mineral deposits on the inside the storage tank of the water heater.

Plano Water Heater Repair PreventionHot Water Heater Repair Plano

Property owners, even individuals which really do not feel very handy, can achieve a great deal of water heater upkeep on their own. Even though much of the time, water heaters are risk-free, it is critical to remember that they actually operate from electrical power and/or gas, and so suitable safety methods should be used. Remember to make use of these tips as an informative tutorial, for we’d much rather demonstrate all these together with you directly. The electric power to the water heater requires to be switched off prior to carrying out any servicing. Ones breaker box ought to have a ideally labeled switch to reveal which breaker is the heater’s. With a gas heater, turn the gas cutoff counterclockwise to switch off the gas to the device.

The component of the heater that assists with controlling rusting within the water storage tank are the anode rods, or additionally termed sacrificial anode rods. A good number of are constructed from aluminum or magnesium around a steel wire. With time the external covering of the rods will erode and they need to be replaced as soon as the steel wire is seen. They commonly last around 5 years, though that is reduced if ones water is soft. In the long term, it is simpler and more affordable to have the anode rods changed, to be able to obtain an extended life from the water heater storage tank. The rods ought to be examined every year basis.

The follow video does a good job of showing the procedure needed with replacing the anode rods:

Not every water heater has dip tubes. They must be looked at for deterioration every 6 months. To test it, take it out and check its length to the height of the water heater. It ought to be about 6″ to 8″ shorter in comparison with the tank. When it’s smaller than that, or possibly demonstrates symptoms of breakage or falling apart, it’ll need to get changed.

The big and small flush. Once again, mineral deposits are the biggest reason of water heater malfunctions. Based on the level of quality of water in ones household will establish just how quickly sediment will build up on the inside of the storage tank. This sediment can solidify with time, creating weird popping sounds from the storage tank, lower the effectiveness of the device, and possibly block the drain valve. Ideally, every 6 months, but a minimum of yearly, empty 1 or 2 gallons of water from the drain valve in the bottom of the hot water heater in a pail or by a hose in a container outdoors. Look to discover just how much sediment is within the pail when the water settles. If it appears to be relatively clear, that great! When these types of small flushes are accomplished two times annually, one might not need to execute a big flush as frequently. If the water appears very dirty, a full flush really should be done. This is certainly likewise a very good occasion to ensure the bottom drain valve of the storage tank is operating nicely and not leaking. They are typically made from plastic and as time passes when they aren’t opened up, they are going to get stuck or not close up securely, so opening and closing them throughout the small flush test is very good.

There can be various techniques one may take through flushing to address any sort of water smells that might develop when hot water comes from faucets within the house also.

This video exhibits exactly how and reasons behind a water heater flush:

Pertaining to holiday or temporary properties, one ought to empty the storage tank of all its water to avoid any kind of flooding when the property is not being occupied. Needless to say, be sure to fill it up whenever the dwelling is to be resided in once again.

Water pipe inspection. Analyze to ensure all water piping don’t have leaks or are harmed at all. It ought to be simple to see when there are any leaks coming from any section of the water plumbing or storage tank for one will see water beneath and/or close to the device. Leaking water can lead to water damage to elements of ones household, so ensure all appears dry, particularly if the heater is found inside of the residence and not in a garage.Plano Water Heater Repair

T&P valve evaluation. The T&P valve, otherwise known as the temperature and pressure relief valve, really should be examined every year. The function of the T&P valve would be to guard the water heater storage tank from excessive pressure, and exploding, not to frighten anybody. The owners guide ought to be looked over to be sure the suitable methods are implemented but listed below are the general measures. A little water can come out of the valve and will probably be really hot so be aware. Lift up the handle and let go of it. Have a container all set to catch any unwanted water which could come out. Additionally, the noise of pressure getting discharged will be observed. The handle ought to snap back in position. In case it does not give it a try once more. If perhaps it will not go back again into position following several attempts, it is going to have to be changed. The valve may perhaps drip a little water after doing that for a little while. If it doesn’t quit dripping after several hours inform us.

There exists a great deal of discussion around what the most effective temperature setting ought to be. The manufacturer pre-programmed setting is normally 140 degrees, which is actually warmer than the majority of people may ever require. 120 degrees is the typical temperature and some individuals actually go as far as 100 degrees. We are publishing much more on this subject matter shortly, but we advise not going over 120 degrees.

Just For Gas Water HeatersWater Heater Repair Plano

The gas venting system requires being looked over each 3 months. Look at to guarantee all fittings are tight and for obstructions and deterioration to the vent pipes together with being sure these are totally free of rust and deterioration .. Gas fired hot water heaters vent fumes to the outdoors of the household. If these fumes flow in the house it could be unsafe and a fire risk. Ensure everything combustible or corrosive is far from the exhaust ventilation to prevent fires. Change all loose, broken or corroded portions of vent pipes.

Take a look at the pilot light to execute a visual examination of just how it is working. The pilot light is the component that ignites the gas burner which heats the water. A clean burning and correctly adjusted pilot light is necessary for your water heater to function at peak efficiency. The color of the flame of the pilot light needs to be blue with natural gas heaters or blue/green with just a bit of yellow at the tip with propane heaters. A weakened flame, a yellow flame, or a flame which has a divided flame on the top suggests that a realignment is required.

Just For Electric Water Heaters

Applying insulation wraps or covers around the storage tank can help hold a continuous temperature inside of the storage tank without needing as much power. As well, with the heater not needing to operate as much will lengthen the life span of the heating element given that it will not be utilised as much. Every 3 months approximately, verify to verify the insulation cover remains attached effectively and hasn’t fallen or shifted on the water storage tank.

Regular examination of the heating element is significant and can help lessen the need for an unexpected emergency repair. We aren’t going to get into the particulars for a complete examination in this article, however one will require a voltage/OHM meter to assure there exists a closed electrical circuit. Heating elements will need changing sometimes.

Continue to keep the vicinity about ones water heater thoroughly clean of dirt. Specifically if the water heater is found in the garage area, be sure to keep the place swept. The cleaner the heater is, the far better it is going to run without having the requirement of a water heater repair.

Replace Old Water Heaters With Energy Efficient Ones

Today, almost all water heaters manufactured have a relatively good quantity of energy efficiency. In April of 2015, new rules were set up in the United States on water heaters. Clearly, the better the heater, the longer the life one will receive from the device using the right routine maintenance through the years. Don’t think twice to contact Hot Water Heater Repair Plano to talk about water heater maintenance or perhaps to help answer any queries on picking the most suitable replacement water heater for ones residence or workplace. Brand, model, and size must all be considered through the selection process and not merely utilize the “bigger the better” slogan. Regarding storage tank water heaters, one will not desire to be continuously retaining a surplus quantity of hot water that won’t be used.

Why is My Plano Yard Wet

Posted by on Jun 10, 2015 in Plumbing Repair Plano | 0 comments

If you discover that you have damp areas in your yard, do not be reluctant to make contact with Plumbing Repair Plano shortly.

Have you have actually experienced any of the following problems in your lawn. Have you observed an odor that penetrates throughout an area of your lawn? Exist any areas of the lawn that appear to constantly have water worked out in them? These are 2 indications that either an underground water line or a sewage system line is actually spilling water into the ground water.Plumbing Repair Plano

Just how and why does this occur? One reason might be root penetration. A sewage system line for a water line may be permeated our even burst by a tree root. It is extraordinary how strong tree roots can be. Clearly, the tree roots do not expand unbelievably quick however the continuous pressure on the plumbing can damage it triggering a pinhole leakage, or ultimately crush and burst the pipe totally. When this occurs, the water from the plumbing or the waste water from the sewage system pipe leakages out into the lawn.

A 2nd cause for this is a collapsed pipe. Simply with the weight of dirt on top of pipes, or in a specific location of high erosion which has actually put even more dirt on top of the pipes, overtime, the pipes will at some point break down. One might likewise have issues with reduced water pressure or a sewage system blockage when a broken down pipe happens. Although we to most likely think about our house’s plumbing simply belonging of the internal structure of your house, one have to bear in mind the capacity for leakages outside the house also.

Don’t hesitate to contact us with any plumbing or water heater repair Plano issue you might be having.

Ideal Water Heater Temperature Setting

Posted by on May 5, 2015 in Gas Water Heater Repair Plano, Tankless Water Heater Repair Plano, Water Heater Repair Plano | 0 comments

Today Water Heater Repair Plano is going to be checking out the diverse feelings on exactly what temperature level a water heater should be established. We will have a look at a few of the various ideas with particular information from those sources to make sure that one may make his/her own conclusion on the issue.

To start with, the by default setting a large number of water heater companies have their tanks placed at is 140 degrees. If this is something you have never examined, that may possibly be what it is set at. Likewise, it can be hard to understand for certain exactly what the temperature setting is due to the fact that lots of times the temperature level dial will not have actual degrees printed on it, simply warm, hot, really hot … something to that end. Some think brands have a high pre-set temperature level to look outstanding to have a great deal of hot water – sort of like attempting to produce excellent brand name recognition.

In regards to energy cost savings, by simply changing the water heater level from 140 to 120 degrees, will conserve around 6 to 10 % of energy usage. That translates to in between $6 to $20 yearly in a lot of cases.

Let’s begin with perhaps the most popular resource, the U.S. Department of Energy. They recommend a setting of 120 degrees. The link to their website above offers fine material on exactly how to decrease ones hot water use and expenses. It is for sure well worth a read.

There can be health threats with having a temperature level setting that is too low. It can be concluded that Legionella bacteria has the optimum development range in between 68 to 122 degrees. It is assumed that 25 % of all water heaters are infected with Legionella bacteria at differing levels.

Legionella bacteria triggers a kind of pneumonia and is transferred to people any time one breathes in water infected with the bacteria – generally in showers and even AC systems. It is typically okay to ingest the water. It is a concern when the germs enter into ones lungs.

The Centers for Disease Control and Prevention approximates 8,000 to 18,000 Americans get the condition yearly. 5 to 30 % of the instances are deadly.

According to OSHA, “At low levels of contamination, the chance of getting Legionnaires’ disease from a water source is very slight. The problem arises when high concentrations of the organism grow in water systems. Water heaters, cooling towers, and warm, stagnant water can provide ideal conditions for the growth of the organism.”  (read more)

There are conditions when one is not going to need the water heater temperature level to be set at 140 degrees also. If there are little youngsters in the residence or possibly with elderly individuals, this may be way too high of a temperature. The possibility of getting burned if the faucet was totally on hot water can be way too great. Certainly, anybody living in the house that is at threat of contracting Legionella Disease ought to have it set at 140 degrees.

In conclusion

So come to a decision if there are any fears of family members becoming burnt if the water temperature level is too hot. Furthermore, be alert of any individual who may have worries of being infected with Legionella Disease. Because the annual expense savings of turning the temperature level down is just about $20 the majority of time with the normal residence’s hot water use, it could be an excellent choice to maintain the temperature level above 120 degrees merely for the well being related advantages; nonetheless, Water Heater Repair Plano TX will let you determine that.

The following infographic sums up our discussion effectively:

Hot Water Heater Repair Plano

Why is My Plano Water Heater Making Noise

Posted by on Jan 13, 2014 in Water Heater Repair Plano, Water Heater Use and Care | 0 comments

Water heaters aren’t known to make too much noise when they are operating, so it can be worrying when one begins to hear popping, banging or rumbling noises originating from the system. Today Water Heater Repair Plano is going to talk about the most usual reason why your water heater may start making banging and exactly what one can do to quiet it down!

Water Heater Repair Plano

Water heater (Photo credit: km6xo)

The most likely reason your water heater is making banging

The most likely description behind your water heating making banging is that sediment has built up on the bottom of your tank. This sediment is usually comprised of calcium and magnesium deposits from your tap water, and it’s specifically common in homes that have hard water.

When sediment builds up at the bottom of your water heater’s tank, it traps some hot water under it. As this takes place, hot water bubbles start to form and break through the sediment. This typically results in a “popping” noise that is heard regularly while your water heater is running.

In addition, the sediment itself might be liable for different water heater noises. That’s due to the fact that the sediment is close to your water heater’s burning elements, which triggers it to burn up and make different odd noises. As water flows throughout the water heater, sediment can likewise break away from the bottom and bang against the walls of the tank.

Ways to stop your water heater from making noise

If your water heater is making sound because of sediment buildup, the first thing one need to do is to have it assessed for an apparent cause. Water Heater Repair Plano TX can do this for you and if sediment accumulation is the culprit, we can flush the water heater tank or recommend an additional option to fix the issue.

There are likewise a number of things you can do to prevent sediment from developing inside the storage tank in the first place. The first is to make certain you receive professional maintenance done on your water heater once each year. During maintenance, we’ll flush your tank and clear away any sediment that has developed since the last maintenance consultation.

An additional wonderful option is to set up a water softener in your house. A water softener removes minerals from your water before they can enter the water heater, which can considerably decrease sediment buildup inside the storage tank.

If you have any concerns about your water heater making sounds offer Water Heater Repair Plano a call today.

Enhanced by Zemanta

Water Heater Safety Advice

Posted by on Dec 3, 2013 in Water Heater Repair Plano, Water Heater Use and Care | 0 comments

Appropriately maintaining ones water heater is important not so it works to its full potential and can conserve some energy cash, however for security issues too. Yes, it can explode – it does not occur too frequently for homeowners, but undoubtedly this is something that Water Heater Repair Plano does not wish to have take place to you!

Vents
Venting can be sort of technical but we will go over the basics below. The vent ought to be the same diameter as the draft diverter of the water heater tank. It is expected to increase and out (for atmospherically vented heaters). Not other directs like up, down, up and out. For direct-vent water heaters, the vent ought to head out a side wall. When it comes to power-vent heaters, the fan blows the fumes out, so there is some versatility in the direction they are vented.

Any roofing system or wall that the vent goes through should be a double wall. The single wall pass throughs need to be screwed with three screws per section. If these fundamentals are not abided by, the vents can break down with time and carbon monoxide can cause significant issues within ones house. Naturally we don’t desire that to occur!

The only other interested in ventilation is that of backdrafting. The fumes can consume the vents with acid condensation. If enough of this gets on cold piping and the water heater it will not be a great circumstance for a properly working water heater. If the fumes return inside the rather of being effectively vented outside, the fumes can get in the living areas of the home. Soot problems can develop too.

Dielectric Connectors
The steel water heater is linked to cooper pipes by the dielectric connectors. When 2 these 2 metals are assembled in water electrolysis happens. The process wears away one metal away to safeguard the other. This procedure is crucial in shielding the inside of the water heater. Inspection for leaks ought to be done where the connections are made.

Temperature and Pressure Relief Valve
This is kinda of a vital part of the water heater, for it helps ensure the darn thing does not explode under pressure if the temperature level goes beyond the appropriate limitations the water heater is created for. Once a year (at least) the T&P valve must be checked to ensure, it is working effectively, for they can be vulnerable to failure. Simply pulling up on the handle water ought to stream freely out and stop when the handle is released. If it just runs or trickles, or does nothing at all, it will need to be replaced.

The drain lines for the T&P line should not be routed up, because water does not flow uphill too well. Make sure it goes down and or out please. If water is running out the drain line routinely, it is the indication of something wrong too. It might be one of numerous different things that we will not enter here – simply call a regional plumbing technician please.

Earthquake Straps
Yep, even if you don’t stay in an earthquake area and are needed to have these on ones water heater, it is a pretty good concept to do so. It appears like a lot of all brand-new homes in sub-divisions nowadays have the water heater in the garage. Yes, there is generally a concrete curb in front of it so one does not drive a vehicle into it, however things can accidentally knock it over so be safe and strap that say thanks to in.

Temperature Level Setting
It appears most residential water heater tanks have settings of warm – hot – very hot … and not degree markings. Some “tips” on conserving energy at home particularly in the winter season time, state to lower the setting on the tank to 120 degrees. That’s fantastic for saving energy however legionella bacteria, which causes Legionnaire’s illness can expand at 120 degrees. By inhaling the mist from the water in the shower, one can inhale the germs. Try to find a medium in between 130 and 120 degrees. Above 130 degrees is technically a scalding temperature level so beware.

Anode Rods
These normally are made of aluminum and there is nothing wrong with that in theory, though we recommend using magnesium ones. Let’s state for whatever reason there is some kind of emergency or disaster where one lives and one needed to use the water in the water heater for drinking water (since bunches of emergency preparedness people suggest doing this). The water that comes out of the drain valve is the water at the bottom of the tank. If one has aluminum anodes, that water will be loaded with aluminum substances, which is bad for the human body. It is bad for the stomach, intestinal tract and joints.

The anodes help with rust defense and are essential in extending the life of the water heater. They can also aid with odor troubles with the water. Overall, magnesium anodes just work much better for a great deal of various reasons like the health perks, let develop up of sediment, a quieter water heater, and they have the tendency to work much better with softened water.

Drain Valve
Okay, just inspect it at least once a year to make sure the darn thing opens and works. And it is excellent to drain and flush the tank at least once a year anyhow (something you of course are doing already). If for some reason one needs to make use of the water throughout a catastrophe or drain it to rather a noisy tank and have actually not drained it routinely, and it doesn’t open, it will take longer to fix the issue you are initially attempting to fix.

Combustion Changer Hatch
Given that gas and oil water heaters breathe the air sucked in from beneath, combust with it and exhale it, it is essential to keep the location around it, specifically beneath the water heater, clean and swept. If if is not burning effectively, it can trigger preparing issues (pointed out above), as well as combustion and fume problems and potentially be a fire risk. Some of examining the chamber and how the flame burns is objective so we are not going to go into a bunch of detail below. it is necessary to see if the combustion chamber roof has a great deal of rust or water markings or is black in color. These are not an excellent sign at all. One ought to see some blue flame at the bottom when it burns and orange and yellow at the top, however, the yellow need to not be incredibly high up. One ought to see gray metal, some white condensation marks are okay.

Water Heater Repair Plano has put together an infographic to highlight the information above:

Water Heater Repair Plano

Check even more water heater maintenance tips here.

Enhanced by Zemanta